7.1. Introduction to if

7.1.1.1. Expressions used with if

The table below contains an overview of the so-called "primaries" that make up the TEST-COMMAND command or list of commands. These primaries are put between square brackets to indicate the test of a conditional expression.

Expressions may be combined using the following operators, listed in decreasing order of precedence:

The [ (or test) built-in evaluates conditional expressions using a set of rules based on the number of arguments. More information about this subject can be found in the Bash documentation. Just like the if is closed with fi, the opening angular bracket should be closed after the conditions have been listed.

7.1.1.2. Commands following the then statement

The CONSEQUENT-COMMANDS list that follows the then statement can be any valid UNIX command, any executable program, any executable shell script or any shell statement, with the exception of the closing fi. It is important to remember that the then and fi are considered to be separated statements in the shell. Therefore, when issued on the command line, they are separated by a semi-colon.

In a script, the different parts of the if statement are usually well-separated. Below, a couple of simple examples.

7.1.1.3. Checking files

The first example checks for the existence of a file:

anny ~> cat msgcheck.sh
#!/bin/bash

echo "This scripts checks the existence of the messages file."
echo "Checking..."
if [ -f /var/log/messages ]
  then
    echo "/var/log/messages exists."
fi
echo
echo "...done."

anny ~> ./msgcheck.sh
This scripts checks the existence of the messages file.
Checking...
/var/log/messages exists.

...done.

7.1.1.4. Checking shell options

To add in your Bash configuration files:

# These lines will print a message if the noclobber option is set:

if [ -o noclobber ]
  then
	echo "Your files are protected against accidental overwriting using redirection."
fi

The environment

The above example will work when entered on the command line: anny ~> if [ -o noclobber ] ; then echo ; echo "your files are protected against overwriting." ; echo ; fi your files are protected against overwriting. anny ~> However, if you use testing of conditions that depend on the environment, you might get different results when you enter the same command in a script, because the script will open a new shell, in which expected variables and options might not be set automatically.

7.1.2.1. Testing exit status

The ? variable holds the exit status of the previously executed command (the most recently completed foreground process).

The following example shows a simple test:

anny ~> if [ $? -eq 0 ]
More input> then echo 'That was a good job!'
More input> fi
That was a good job!

anny ~>

The following example demonstrates that TEST-COMMANDS might be any UNIX command that returns an exit status, and that if again returns an exit status of zero:

anny ~> if ! grep $USER /etc/passwd
More input> then echo "your user account is not managed locally"; fi
your user account is not managed locally

anny > echo $?
0

anny >

The same result can be obtained as follows:

anny > grep $USER /etc/passwd

anny > if [ $? -ne 0 ] ; then echo "not a local account" ; fi
not a local account

anny >

7.1.2.2. Numeric comparisons

The examples below use numerical comparisons:

anny > num=`wc -l work.txt`

anny > echo $num
201

anny > if [ "$num" -gt "150" ]
More input> then echo ; echo "you've worked hard enough for today."
More input> echo ; fi

you've worked hard enough for today.


anny >

This script is executed by cron every Sunday. If the week number is even, it reminds you to put out the garbage cans:

#!/bin/bash

# Calculate the week number using the date command:

WEEKOFFSET=$[ $(date +"%V") % 2 ]

# Test if we have a remainder.  If not, this is an even week so send a message.
# Else, do nothing.

if [ $WEEKOFFSET -eq "0" ]; then
  echo "Sunday evening, put out the garbage cans." | mail -s "Garbage cans out" your@your_domain.org

7.1.2.3. String comparisons

An example of comparing strings for testing the user ID:

if [ "$(whoami)" != 'root' ]; then
        echo "You have no permission to run $0 as non-root user."
        exit 1;
fi

With Bash, you can shorten this type of construct. The compact equivalent of the above test is as follows:

[ "$(whoami)" != 'root' ] && ( echo you are using a non-privileged account; exit 1 )

Similar to the "&&" expression which indicates what to do if the test proves true, "||" specifies what to do if the test is false.

Regular expressions may also be used in comparisons:

anny > gender="female"

anny > if [[ "$gender" == f* ]]
More input> then echo "Pleasure to meet you, Madame."; fi
Pleasure to meet you, Madame.

anny >

	Real Programmers
	Most programmers will prefer to use the test built-in command, which is equivalent to using square brackets for comparison, like this: test "$(whoami)" != 'root' && (echo you are using a non-privileged account; exit 1)

See the info pages for Bash for more information on pattern matching with the "(( EXPRESSION ))" and "[[ EXPRESSION ]]" constructs.